GAUSS-50600 -- GAUSS-50699

GAUSS-50600: “The IP address cannot be pinged, which is caused by network faults.”

SQLSTATE: None

Description: Failed to ping the IP address.

Solution: Change the network settings so that the IP address can be pinged.

GAUSS-50601: “The port [%s] is occupied.”

SQLSTATE: None

Description: The port is occupied.

Solution: Check whether the resources that occupy the port number are available. If the resources are idle, release the port number. Specify other port numbers.

GAUSS-50602: “Failed to bind network adapters.”

SQLSTATE: None

Description: Failed to bind the NIC.

Solution:Contact technical support.

GAUSS-50603: “The IP address is invalid.”

SQLSTATE: None

Description: The IP address is invalid.

Solution: Correct the IP address.

GAUSS-50604: “Failed to obtain network interface card of backIp(%s).”

SQLSTATE: None

Description: Failed to obtain the NIC.

Solution: Check whether the network is normal. Check whether the NIC is normal.

GAUSS-50605: “Failed to obtain back IP subnet mask.”

SQLSTATE: None

Description: Failed to obtain the subnet mask.

Solution: Check whether the network is normal.

GAUSS-50606: “Back IP(s) do not have the same subnet mask.”

SQLSTATE: None

Description: The backIp cannot have the same subnet mask.

Solution: Set a subnet mask to the backIp.

GAUSS-50607: “Failed to obtain configuring virtual IP line number position of network startup file.”

SQLSTATE: None

Description: Failed to obtain the virtual IP address in the NIC startup file.

Solution: Manually check the NIC configuration file to see whether the file is damaged.

GAUSS-50608: “Failed to writing virtual IP setting cmds into init file.”

SQLSTATE: None

Description: Failed to write the virtual IP configuration command in the initialization file.

Solution: Manually check the NIC configuration file to see whether the file is damaged.

GAUSS-50609: “Failed to check port: %s.”

SQLSTATE: None

Description: Failed to check the port.

Solution: Ensure that the port is enabled and not occupied.

GAUSS-50610: “Failed to get the range of random port.”

SQLSTATE: None

Description: Failed to obtain the port range.

Solution: Check the cause of the failure and obtain the range again.

GAUSS-50611: “Failed to obtain network card bonding information.”

SQLSTATE: None

Description: Failed to obtain the NIC binding information.

Solution: Check whether the **/proc/net/bonding/**NIC__ __ID file exists, whether the BONDING_OPTS (the Red Hat environment) or BONDING_MODULE_OPTS (the CentOS environment) strings exist.

GAUSS-50612: “Failed to obtain network card %s value.”

SQLSTATE: None

Description: Failed to obtain the value of the NIC RTU/RX.

Solution: Check whether the network is normal and whether the NIC is normal.

GAUSS-50613: “Failed to set network card %s value.”

SQLSTATE: None

Description: Failed to set the NIC information.

Solution: Check whether the network is normal and whether the NIC is normal.

GAUSS-50614: “Failed to check network information.”

SQLSTATE: None

Description: Failed to check the NIC information.

Solution: Check whether ifconfig is available. If it is, query it again.

GAUSS-50615: “IP %s and IP %s are not in the same network segment.”

SQLSTATE: None

Description: The network segments of the two IP addresses are different.

Solution: Set the network segments of the two IP addresses to the same network segment. Then, perform the operation again.

GAUSS-50616: “Failed to get network interface.”

SQLSTATE: None

Description: Failed to obtain the network interface.

Solution: Ensure that the IP address exists, ifconfig is available, and IP information exists in the NIC configuration file. Then, perform the operation again.

GAUSS-50617: “The node of XML configure file has the same virtual IP.”

SQLSTATE: None

Description:Internal system error.

Solution:Contact technical support.

Feedback
编组 3备份
    openGauss 2024-07-19 01:03:13
    cancel